Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADIFLAM A FR 5138 OR - PA66 - RadiciGroup High Performance Polymers

Material Data Center offers the following functions for RADIFLAM A FR 5138 OR:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Radiflam A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
기계적 특성 - 열적 특성 - 전기적 특성 - 기타 특성
Any use of this information falls under the rules of our disclaimer.
제품 설명서
PA66 flame retardant injection moulding grade. Halogen and red phosphorus free. Orange colour.

Suitable for parts where fire retardancy is required. Rated V-0 at 0.4 mm according to UL-94. Also suitable for monofilament extrusion.
기계적 특성건조/응축단위시험규격
ISO 데이터
인장탄성률 3400 / - MPa ISO 527
항복강도 75 / - MPa ISO 527
항복변형률 4.1 / - % ISO 527
파단시 평균신율 6 / - % ISO 527
챠피 충격 강도 , +23°C 50 / - kJ/m² ISO 179/1eU
챠피 충격 강도, -30°C 52 / - kJ/m² ISO 179/1eU
챠피 노치드 충격 강도, +23°C 2.3 / - kJ/m² ISO 179/1eA
챠피 노치드 충격 강도, -30°C 2.3 / - kJ/m² ISO 179/1eA
열적 특성건조/응축단위시험규격
ISO 데이터
녹는점, 10°C/min 255 / * °C ISO 11357-1/-3
하중하에서의 변형온도, 1.80 MPa 70 / * °C ISO 75-1/-2
두께 H인 제품의 난연성 V-0 / * class IEC 60695-11-10
테스트 두께 0.8 / * mm -
Yellow Card 유효한 예 / * - -
전기적 특성건조/응축단위시험규격
ISO 데이터
부피 저항 1E13 / 1E11 Ohm*m IEC 62631-3-1
표면 저항 * / 1E10 Ohm IEC 62631-3-2
CTI 600 / - - IEC 60112
기타 특성건조/응축단위시험규격
밀도 1190 / - kg/m³ ISO 1183
특징
생산 공정
사출 성형
인도 유형
과립
부가물
이형제
특별 특성
난연성, Halogen-free, Phosphorus-free, 열안정성
응용
Monofilament
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬, 쨉쩔쩐챌 쨔횞 쩐횈횉횁쨍짰횆짬 짹횢쩔짧
기타 정보
사E성
The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.10%. Typical conditions with a desiccant drier: temperature 80 ° C, dew point -20 ° C or below, time 2-4 h or more. Avoid excessive shear rates and high thermal stresses for better processing. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters
Melt TemperatureMold TemperatureInjection Speed
270 - 290°C 60 - 80°Cmedium


Extrusion Temperature
270 - 290°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.